Harsh Sharma Technicals

Everything About Technology At One Place

Codes And Circuit DiagramsLatest

Code And Circuit Diagram For Fingerprint Sensing Door Locking System

If you want to buy the entire combo for the project then click here

Enrollment Code (Code 1)

#include <Adafruit_Fingerprint.h>
#include <SoftwareSerial.h>
SoftwareSerial mySerial(2, 3); //you can change them if it is not working on 2 or 3

Adafruit_Fingerprint finger = Adafruit_Fingerprint(&mySerial);

uint8_t id;

void setup()
{
Serial.begin(9600);
while (!Serial); // For Yun/Leo/Micro/Zero/…
delay(100);
Serial.println(“\n\nFingerprint sensor enrollment”);

// set the data rate for the sensor serial port
finger.begin(57600);

if (finger.verifyPassword()) {
Serial.println(“Found fingerprint sensor!”);
} else {
Serial.println(“Did not find fingerprint sensor :(“);
while (1) { delay(1); }
}
}

uint8_t readnumber(void) {
uint8_t num = 0;

while (num == 0) {
while (! Serial.available());
num = Serial.parseInt();
}
return num;
}

void loop() // program wil repeat this part (loop here)
{
Serial.println(“Ready to enroll a fingerprint!”);
Serial.println(“Please type in the ID # (from 1 to 127) you want to save this finger as…”);
id = readnumber();
if (id == 0) {// ID #0 not allowed, try again!
return;
}
Serial.print(“Enrolling ID #”);
Serial.println(id);

while (! getFingerprintEnroll() );
}

uint8_t getFingerprintEnroll() {

int p = -1;
Serial.print(“Waiting for valid finger to enroll as #”); Serial.println(id);
while (p != FINGERPRINT_OK) {
p = finger.getImage();
switch (p) {
case FINGERPRINT_OK:
Serial.println(“Image taken”);
break;
case FINGERPRINT_NOFINGER:
Serial.println(“.”);
break;
case FINGERPRINT_PACKETRECIEVEERR:
Serial.println(“Communication error”);
break;
case FINGERPRINT_IMAGEFAIL:
Serial.println(“Imaging error”);
break;
default:
Serial.println(“Unknown error”);
break;
}
}

// OK success!

p = finger.image2Tz(1);
switch (p) {
case FINGERPRINT_OK:
Serial.println(“Image converted”);
break;
case FINGERPRINT_IMAGEMESS:
Serial.println(“Image too messy”);
return p;
case FINGERPRINT_PACKETRECIEVEERR:
Serial.println(“Communication error”);
return p;
case FINGERPRINT_FEATUREFAIL:
Serial.println(“Could not find fingerprint features”);
return p;
case FINGERPRINT_INVALIDIMAGE:
Serial.println(“Could not find fingerprint features”);
return p;
default:
Serial.println(“Unknown error”);
return p;
}

Serial.println(“Remove finger”);
delay(2000);
p = 0;
while (p != FINGERPRINT_NOFINGER) {
p = finger.getImage();
}
Serial.print(“ID “); Serial.println(id);
p = -1;
Serial.println(“Place same finger again”);
while (p != FINGERPRINT_OK) {
p = finger.getImage();
switch (p) {
case FINGERPRINT_OK:
Serial.println(“Image taken”);
break;
case FINGERPRINT_NOFINGER:
Serial.print(“.”);
break;
case FINGERPRINT_PACKETRECIEVEERR:
Serial.println(“Communication error”);
break;
case FINGERPRINT_IMAGEFAIL:
Serial.println(“Imaging error”);
break;
default:
Serial.println(“Unknown error”);
break;
}
}

// OK success!

p = finger.image2Tz(2);
switch (p) {
case FINGERPRINT_OK:
Serial.println(“Image converted”);
break;
case FINGERPRINT_IMAGEMESS:
Serial.println(“Image too messy”);
return p;
case FINGERPRINT_PACKETRECIEVEERR:
Serial.println(“Communication error”);
return p;
case FINGERPRINT_FEATUREFAIL:
Serial.println(“Could not find fingerprint features”);
return p;
case FINGERPRINT_INVALIDIMAGE:
Serial.println(“Could not find fingerprint features”);
return p;
default:
Serial.println(“Unknown error”);
return p;
}

// OK converted!
Serial.print(“Creating model for #”); Serial.println(id);

p = finger.createModel();
if (p == FINGERPRINT_OK) {
Serial.println(“Prints matched!”);
} else if (p == FINGERPRINT_PACKETRECIEVEERR) {
Serial.println(“Communication error”);
return p;
} else if (p == FINGERPRINT_ENROLLMISMATCH) {
Serial.println(“Fingerprints did not match”);
return p;
} else {
Serial.println(“Unknown error”);
return p;
}

Serial.print(“ID “); Serial.println(id);
p = finger.storeModel(id);
if (p == FINGERPRINT_OK) {
Serial.println(“Stored!”);
} else if (p == FINGERPRINT_PACKETRECIEVEERR) {
Serial.println(“Communication error”);
return p;
} else if (p == FINGERPRINT_BADLOCATION) {
Serial.println(“Could not store in that location”);
return p;
} else if (p == FINGERPRINT_FLASHERR) {
Serial.println(“Error writing to flash”);
return p;
} else {
Serial.println(“Unknown error”);
return p;
}
}

If you are getting a stray error while uploading then download the code from here 

Fingerprint Unlock Code (Code 2)

#include <Adafruit_Fingerprint.h>
#include <SoftwareSerial.h>

SoftwareSerial mySerial(2, 3);

Adafruit_Fingerprint finger = Adafruit_Fingerprint(&mySerial);

void setup()
{
Serial.begin(9600);
while (!Serial); // For Yun/Leo/Micro/Zero/…
delay(100);
Serial.println(“fingertest”);
pinMode(12, OUTPUT);
pinMode(11, OUTPUT);

// set the data rate for the sensor serial port
finger.begin(57600);

if (finger.verifyPassword()) {
Serial.println(“Found fingerprint sensor!”);
} else {
Serial.println(“Did not find fingerprint sensor :(“);
while (1) {
delay(1);
}
}

finger.getTemplateCount();
Serial.print(“Sensor contains “); Serial.print(finger.templateCount); Serial.println(” templates”);
Serial.println(“Waiting for valid finger…”);
}

void loop() // run over and over again

{
getFingerprintIDez();
delay(50); //don’t ned to run this at full speed.
digitalWrite(12, LOW);
digitalWrite(11, LOW);
}

uint8_t getFingerprintID() {
uint8_t p = finger.getImage();
switch (p) {
case FINGERPRINT_OK:
Serial.println(“Image taken”);
break;
case FINGERPRINT_NOFINGER:
Serial.println(“No finger detected”);
return p;
case FINGERPRINT_PACKETRECIEVEERR:
Serial.println(“Communication error”);
return p;
case FINGERPRINT_IMAGEFAIL:
Serial.println(“Imaging error”);
return p;
default:
Serial.println(“Unknown error”);
return p;
}

// OK success!

p = finger.image2Tz();
switch (p) {
case FINGERPRINT_OK:
Serial.println(“Image converted”);
break;
case FINGERPRINT_IMAGEMESS:
Serial.println(“Image too messy”);
return p;
case FINGERPRINT_PACKETRECIEVEERR:
Serial.println(“Communication error”);
return p;
case FINGERPRINT_FEATUREFAIL:
Serial.println(“Could not find fingerprint features”);
return p;
case FINGERPRINT_INVALIDIMAGE:
Serial.println(“Could not find fingerprint features”);
return p;
default:
Serial.println(“Unknown error”);
return p;
}

// OK converted!
p = finger.fingerFastSearch();
if (p == FINGERPRINT_OK) {
Serial.println(“Found a print match!”);
} else if (p == FINGERPRINT_PACKETRECIEVEERR) {
Serial.println(“Communication error”);
return p;
} else if (p == FINGERPRINT_NOTFOUND) {
Serial.println(“Did not find a match”);
return p;
} else {
Serial.println(“Unknown error”);
return p;
}
{digitalWrite(11, HIGH);
delay(3000);
digitalWrite(11, LOW);
Serial.print(“Not Found”);
Serial.print(“Error”);
return finger.fingerID;
}

// found a match!
Serial.print(“Found ID #”); Serial.print(finger.fingerID);
Serial.print(” with confidence of “); Serial.println(finger.confidence);

return finger.fingerID;
}

// returns -1 if failed, otherwise returns ID #
int getFingerprintIDez() {
uint8_t p = finger.getImage();
if (p != FINGERPRINT_OK) return -1;

p = finger.image2Tz();
if (p != FINGERPRINT_OK) return -1;

p = finger.fingerFastSearch();
if (p != FINGERPRINT_OK) return -1;

// found a match!

{
digitalWrite(12, HIGH);
delay(3000);
digitalWrite(12, LOW);
Serial.print(“Found ID #”); Serial.print(finger.fingerID);
Serial.print(” with confidence of “); Serial.println(finger.confidence);

} }

If you are getting a stray error while uploading then download the code from here 

 

Circuit Diagram

I am not a professional so haven’t used any editing software like fritz to edit the code. Please bear text me over instagram @harshsharma_6 if you didn’t understand something, i’d be more than happy to help.

Leave a Reply

Your email address will not be published. Required fields are marked *